Where is the VIN number in Audi Q7 (4L) (2006-2015)?

This guide shows where to find the VIN (chassis number) on the Audi Q7 Typ 4L, produced between 2006 and 2015, using the same spots technicians check during inspections and vehicle verification.

Chassis Number Locations

1) Driver’s door jamb / B-pillar VIN label

• Where to look: Open the front door and look at the B-pillar (the post between the front and rear doors). The VIN is printed on a black sticker with white lettering, usually positioned low on the pillar along with axle weight and paint/option codes.
• Access: Easy. No tools needed—just open the door and wipe dust off the sticker if it’s grimy.
• Note: For LHD Q7s, this is typically on the left side (driver’s side). For RHD, it’s typically on the opposite side—if you don’t see it, check the other B-pillar.
• Tip: Because the label is vertical, angle your phone slightly and scan the sticker directly with the VIN reader instead of trying to type characters one-by-one.

2) Windshield VIN plate (dashboard)

• Where to look: From outside the vehicle, look through the windshield at the lower corner of the dashboard area where the VIN plate is visible through the glass.
• Access: Easy to moderate. No disassembly, but glare/reflections can make it hard to read.
• Note: This location is consistent across LHD/RHD markets—only the viewing side/corner may feel more convenient depending on where you’re standing.
• Tip: If sunlight glare washes out the digits, capture it instantly with your phone using ScanVin.app (move the camera closer to the glass and let OCR grab it before reflections shift).

3) Cargo area / boot floor chassis stamp (rear cross-member)

• Where to look: In the rear luggage compartment, the VIN is stamped into metal on the rear cross-member/floor area, close to the rear latch/striker zone near the bumper edge.
  • Access Path A (trim flap style): Lift the main cargo floor panel. Look for a pre-cut flap in the carpet/trim to the right of the spare wheel well and lift it to expose the stamped VIN.
  • Access Path B (toolkit tray style): Lift the main floor and remove the Styrofoam toolkit organizer completely. The stamp is on the metal floor near the rear edge.
• Access: Moderate. You’ll need to clear luggage, lift floor panels, and possibly remove the foam tray. It’s usually dark inside the well—bring a light.
• Note: This stamp location stays the same across markets; the trim/access method can vary by equipment (cargo management/toolkit layout).
• Tip: Because the stamp is often dark-on-dark and sits in shadow, turn on flash and use the flashlight + OCR scanning in ScanVin.app so you don’t misread faint characters while bent over the trunk.

Video Guide

Video Tutorial: AUDI Q7. Engine number, chassis number and chassis plate location

▶ Watch Audi Q7 VIN Location Guide

• Shows the windshield VIN, the boot-floor chassis stamp via carpet flap access, and the door jamb VIN label (also mentions engine number—separate from VIN).

Video Tutorial: Chassis Number location of Audi Q7 - YouTube

▶ Watch Audi Q7 VIN Location Guide

• Demonstrates removing the foam toolkit tray in the trunk to reveal the rear chassis stamp on a different trim variation.

Common Problems & Troubleshooting

• Can’t see the trunk stamp: It’s recessed and poorly lit. Lift the cargo floor fully, remove the foam/tool tray if fitted, and use a flashlight to find the stamped metal area near the rear edge.
• Windshield VIN is unreadable: Glare from sun or overhead lights will mirror the dashboard. Change your viewing angle, shade the glass with your hand, and move the camera closer.
• Sticker vs. stamp mismatch: Door-jamb stickers can be replaced (accident repairs/paintwork). For verification, cross-check the windshield VIN + trunk stamp and ensure they match exactly.