Where is the VIN in the Audi A4?

This guide shows you where to find the VIN (chassis number) on the Audi A4 B9 (8W) produced between 2016–2021, including the quickest “walk-up” VIN label and the stamped VIN in the engine bay.

Chassis Number Locations

1) VIN Sticker (Type Label) — B-Pillar / Door Sill

• Where to look: Open the front door and look at the lower B-pillar (the post between the front and rear doors) right by the door sill. The sticker includes the VIN plus other data (paint code/weights).
• Access: Low difficulty. No tools. You just need to crouch because it’s low to the ground.
• Note: The inspection video vehicle is RHD, showing the label on the right side. On many LHD (EU/US) cars you may find this label on the opposite side—if you don’t see it on one B-pillar, check the other.
• Tip: Because you’re bent down in an awkward position, scan it directly with your phone instead of copying characters by hand.

2) Stamped Chassis Number (VIN) — Right Front Strut Tower

• Where to look: Pop the hood and go to the right-hand suspension strut tower. The VIN is stamped into the metal on top of the tower, near the red jump-start terminal cover.
• Access: Low to Medium. It’s exposed, but it can be dusty/grimy, and the characters are dot-peened (made of small punched dots), which can be harder to read.
• Note: The report indicates the stamped VIN is located on the right strut tower; don’t translate this into “driver side” or “passenger side”—use vehicle left/right orientation.
• Tip: If the stamping is dirty or the dot-peen is faint, wipe it and then use High Contrast AI Mode to scan it so the characters stand out.

3) Engine Number — Top of Engine Block (Under Cover)

• Where to look: The engine number is indicated to be on the top/front area of the engine block, under the main plastic acoustic (“TFSI”) engine cover, near a sensor.
• Access: High difficulty. The number is physically covered unless you remove the plastic engine cover (typically held by grommets and pulls up). The inspection video does not show the digits.
• Note: This is not a good “quick check” location during a basic viewing because access depends on cover removal.
• Tip: If you do remove the cover and the area is shadowy/tight, scan it with your phone to avoid misreading characters in an awkward spot.

Video Guide

Video Tutorial: AUDI A4 TFSI ( PETROL ) VIN / CHASSIS NUMBER & ENGINE NUMBER LOCATION

▶ Watch Audi A4 VIN Location Guide

• Shows the VIN sticker on the door jamb and the stamped chassis number on the right strut tower inside the engine bay.

Common Problems & Troubleshooting

• Dot-peened stamped VIN looks “blurred”: Scrub the area with a rag and use angled light (or your phone light) to create shadows that reveal the dots.
• Engine bay VIN is dirty/greasy: Clean first—oil film can hide the stamping and also confuses camera focus.
• Sticker vs stamped VIN mismatch: If the door-jamb label looks tampered with, always cross-check the stamped chassis VIN before buying.

---

This guide shows the VIN (chassis number) locations on the Audi A4 B8 (8K) produced 2008–2015, including the quick-to-check plates and the more “mechanic-only” stamped number.

Chassis Number Locations

1) Engine compartment (stamped chassis number in plenum chamber)

• Where to look: Open the hood and go to the plenum chamber (the tray area between the engine bay and the windshield). The VIN is stamped into the metal slightly right-of-center when facing the engine (i.e., roughly in front of the passenger seat area).
• Access: You’ll usually need to lift/remove the rubber weather strip and move/pry up the plastic cowling/cover to see the stamp clearly. Expect dirt/leaves and awkward viewing angle near the windshield base.
• Note: On RHD cars, the stamped VIN is still in the same plenum/firewall zone (it does not “swap sides” just because the steering wheel is on the other side).
• Tip: If the stamp is dusty or low-contrast, use the app’s camera with contrast assistance to read it instead of guessing characters—try to scan the stamped VIN in High Contrast AI Mode while shining a light across the letters.

2) Dashboard / windshield VIN plate (region dependent)

• Where to look: Look through the windshield at the bottom corner on the left side of the dash (near the base of the glass).
• Access: Very easy—no tools. The main fight is windshield glare/reflections.
• Note: Some markets may not have a visible windshield VIN plate (you may see a blank/black area instead). If it’s missing, move to the door jamb sticker and the stamped plenum VIN.
• Tip: If reflections wash out the numbers, capture the VIN instantly with your phone so you don’t transpose characters like 8/B, O/0, S/5.

3) B-pillar / door jamb manufacturer sticker

• Where to look: Open a front door and inspect the B-pillar/door jamb area (often lower section). You’re looking for a black or silver manufacturer label listing the VIN, weights, and paint/trim info.
• Access: Usually easy and well-lit. On older cars, the label can fade, peel, or get scratched.
• Note: Location can vary slightly by market (driver/passenger side), so if you don’t see it on one side, check the other front door jamb.
• Tip: This label is great for OCR—use the free VIN reader to scan the sticker rather than typing it by hand.

4) Trunk / boot option-code sticker (spare wheel well)

• Where to look: Open the trunk and lift the floor mat/carpet. Check in or near the spare tire well and the toolkit/foam organizer area for a white paper “vehicle data/PR code” sticker that includes the VIN and option codes.
• Access: Requires unloading/clearing the trunk and lifting panels. Sticker is fragile and can be damaged by moisture or cargo.
• Note: This is a strong backup if the windshield plate is missing or the door sticker is damaged.
• Tip: If the paper is wrinkled or stained, scan it with your phone instead of manually decoding faded print.

5) Service book / paperwork (vehicle data sticker)

• Where to look: Check the owner’s manual folder/glovebox for the maintenance booklet. Many have a “Vehicle Data” sticker (often matching the trunk sticker) and the VIN may also appear on official documents.
• Access: No tools—just find the booklet/documents.
• Note: Paperwork is useful for cross-checking, but always verify against a physical VIN on the car before purchase/registration.
• Tip: For clean, fast entry, scan the VIN from the booklet with OCR rather than retyping long strings.

6) MMI infotainment (digital VIN display)

• Where to look: On many B8 cars with MMI: Car menu → Settings/System → Version information (wording varies). The VIN may be shown in system/version screens.
• Access: Requires battery power and menu navigation; screens can be harder to capture due to refresh/flicker.
• Note: Treat this as a verification point, not the primary legal identifier (physical VINs matter most).
• Tip: If you need to confirm characters you can’t read elsewhere, use the app to store/compare VINs you’ve scanned and spot mismatches quickly.

Video Guide

Video Tutorial: Where is VIN NUMBER Location in AUDI A4 B8 ( 2007 - YouTube

▶ Watch Audi A4 VIN Location Guide

• Clear LHD Audi A4 B8 walkthrough showing the windshield area, the plenum/firewall stamped VIN, and the door jamb sticker.

Video Tutorial: Audi A4 chassis number location ! Audi A4 engine ... - YouTube

▶ Watch Audi A4 VIN Location Guide

• RHD Audi A4 B8 video focusing on the door jamb sticker and the stamped VIN in the plenum chamber area.

Common Problems & Troubleshooting

• Stamped VIN hard to see in the plenum chamber: Leaves, dust, and glare at the windshield base can hide characters—brush debris away and shine a light sideways across the stamp to make it pop.
• Windshield plate unreadable: Reflections on the glass can obscure the VIN—change your viewing angle or shade the area with your hand.
• Sticker mismatch warning: A door/trunk sticker can be replaced or damaged—for any purchase or identity check, confirm the VIN matches the stamped chassis number.

---

This guide shows where to find the VIN (chassis number) on the Audi A4 B7 (8E) (2005–2007) so you can confirm the vehicle identity and scan it accurately with your phone.

Chassis Number Locations

1) Engine Bay – Stamped Chassis Number (Firewall / Plenum Chamber)

• Where to look: Open the hood and go to the rear of the engine bay at the firewall. The VIN is stamped into the metal shelf/plenum chamber, slightly right-of-center (when standing in front of the car facing the engine), forward of the battery area and near the positive jump terminal. You may need to lift a rubber/plastic flap or weather seal to see the full alphanumeric string.
• Access: Expect dust/road grime buildup here. The stamping can be partly covered by the seal—lift it and scrub/wipe the metal before reading. On older cars, watch for surface rust that makes characters faint.
• Note: This location is consistent across steering configurations; the demo car is RHD, but the firewall/plenum stamping is in the same general engine-bay area.
• Tip: If the stamp is dirty or low-contrast, wipe it clean and then use the High Contrast scan mode to read the stamped VIN directly instead of trying to guess faded characters.

2) B-Pillar / Door Jamb VIN Sticker (Lower B-Pillar)

• Where to look: Open the front door and check the lower B-pillar/door jamb area near the sill. Look for a black sticker with white text (sometimes on a silver backing).
• Access: It sits low down, so you’ll likely need to crouch. These stickers can get scuffed from shoes and are often in shadow under the door frame—use extra light.
• Note: The sample shown is RHD; on many LHD cars this label is still on a B-pillar/door jamb area—check both sides if you don’t see it immediately.
• Tip: Because this area is often dark, turn on flash and scan the sticker with your phone to avoid misreading small characters.

3) Dashboard / Windshield (Visible VIN Plate)

• Where to look: Check the lower corner of the windshield where the dash meets the glass (a “visible VIN” window on many markets).
• Access: Main issues are glare/reflections and a dirty windshield. Try viewing from outside with the sun behind you.
• Note: This spot wasn’t shown in the Audi-specific footage, but it’s a common visible VIN location on many EU/US vehicles.
• Tip: If reflections wash out the digits, quickly capture the VIN through the glass so you don’t transpose characters by hand.

Video Guide

Video Tutorial: Audi A4 chassis number location ! Audi A4 engine ... - YouTube

▶ Watch Audi A4 VIN Location Guide

• A mechanic shows the B-pillar VIN sticker and the stamped chassis number in the engine bay, including lifting the seal to expose the full code.

Common Problems & Troubleshooting

• Grime/rust on the engine-bay stamping: Scrub the area with a rag (and mild cleaner) before reading—road dust packs into the stamped characters.
• Seal/trim hiding characters: If you only see part of the VIN, lift the rubber/plastic weather strip along the plenum shelf to reveal the full string.
• Sticker not trustworthy or missing: Door-jamb stickers can be replaced; always cross-check the stamped chassis number against paperwork before buying.

---

This guide shows you where to locate the 17-digit VIN (chassis number) on the Audi A4 B6 (8E/8H) produced between 2001–2004, using the same spots a mechanic checks during an identity inspection.

Chassis Number Locations

1) Engine Bay Bulkhead (Firewall / Plenum Chamber)

• Where to look: Open the hood and look at the plenum chamber at the base of the windshield. The VIN is stamped into the metal firewall, near the center, typically slightly toward the right side of the car (passenger side on LHD), just behind/under the plastic cowling and weather stripping—above hoses and wiring.
• Access: Usually no tools needed, but you may need to lift the rubber weather strip slightly and scrub away leaves/dirt to reveal the stamped characters. Shadows from the hood and nearby hoses are common.
• Note: The videos shown are LHD cars; use the vehicle’s left/right orientation as seen from the rear (direction of travel).
• Tip: If the stamping is dirty or hard to read, wipe it down and use High Contrast AI Mode to scan it directly instead of guessing faded characters.

2) Engine Bay Strut Tower (Manufacturer Data Sticker / Type Label)

• Where to look: In the engine bay on the right-side strut tower area (right inner fender) you’ll find a manufacturer data sticker (type label) that includes the VIN plus weight ratings/paint codes.
• Access: Easy to reach, but on older B6 cars the sticker can be dirty, degraded, peeling, or faded. Some engine bay components (AC lines/air intake area) can limit how close you can get your phone camera.
• Note: This is a great cross-check against the stamped VIN—especially after body repairs—but only if the label is intact.
• Tip: When the sticker is worn or the area is tight, use the VIN scanner to capture it without manually typing and let OCR pull the characters even if the label looks rough.

3) Dashboard / Windshield VIN Plate (region-dependent)

• Where to look: Look through the windshield at the lower corner on the left side of the car (driver side on LHD) for a VIN plate visible from outside.
• Access: Fast check—no tools—but glare/reflections can hide digits depending on sunlight and tint.
• Note: This is common on many US-spec vehicles; some EU-spec cars may not present it the same way.
• Tip: If glare is washing it out, capture it quickly with your phone VIN reader so you don’t misread a 5/S or 8/B.

Video Guide

Video Tutorial: Where is the VIN number of my Audi A4 B6 ( 2000 – 2006 ) - YouTube

▶ Watch Audi A4 VIN Location Guide

• Clear walkthrough of the correct Audi A4 B6 showing the stamped firewall VIN and the engine-bay type sticker (including a real-world example of a dirty/aged label).

Common Problems & Troubleshooting

• Leaves/dirt in the plenum chamber: The firewall stamping can be packed with debris—brush it out and wipe the metal clean before trying to read/scan it.
• Shadowy engine-bay lighting: The hood and hoses can cast shadows—aim a flashlight from the side to make the stamp “pop.”
• Sticker VIN isn’t proof by itself: Engine-bay stickers can be replaced or damaged; for buying/verification, always match the sticker VIN to the stamped chassis VIN and your registration/title.

This guide shows where to find the VIN (chassis number) on the Audi A4 B5 (8D) produced between 1995–2000. If you’re verifying identity before buying, always prioritize the body-stamped VIN first, then cross-check it against the stickers/plates.

Chassis Number Locations

Firewall / Bulkhead (Stamped VIN)

• Where to look: Open the hood and go to the rear of the engine bay. The VIN is stamped into the metal firewall/bulkhead inside the plenum chamber (water box) under the windshield base—typically near the center or slightly to the right side of the car.
• Access: High difficulty. Pry up the rubber weather seal and lift/loosen the plastic rain tray (cowl/debris cover). Expect dirt buildup; the stamping can be recessed and shadowed, and access may be tight around nearby components.
• Note: Works for both Sedan and Avant. “Left/right” here refers to the car’s left/right (direction of travel), not driver position.
• Tip: Because it’s recessed, dark, and often grimy, use the app’s camera plus high-contrast capture to read faint characters—scan it directly with the VIN reader instead of trying to write it down in an awkward position.

Identification Plate (Type Plate)

• Where to look: With the hood open, look for a metal/sticker ID plate on the right-side inner fender reinforcement or on the radiator lock carrier (slam panel) near the headlight.
• Access: Low difficulty. Usually visible immediately; you may only need to wipe dust off the label/plate.
• Note: This is an ID plate, not the main body stamping—use it for cross-checking details.
• Tip: Clean the surface and use the free VIN scanner to OCR the characters accurately if the print is small or partially worn.

Trunk / Spare Wheel Well (Data Sticker)

• Where to look: In the trunk, lift the carpet/floor panel. The white data sticker is typically on the boot floor (often left side under the carpet) or inside the spare wheel well.
• Access: Medium difficulty. Empty the trunk and lift the floor panel/carpet; on older cars (1995–2000) the sticker may be faded, torn, or missing.
• Note: On some Avant (wagon) layouts, the sticker may be in a side storage compartment area rather than centered in the wheel well.
• Tip: If the sticker is faded or stained, capture it with your phone using ScanVin so the AI can help pick up light print you’d miss by eye.

Dashboard VIN (North America Only)

• Where to look: At the lower corner of the windshield on the left side of the car (driver side on LHD US cars), viewed from outside.
• Access: Medium difficulty. Readability depends on lighting; glare/reflection on the glass is common.
• Note: Most EU-spec Audi A4 B5 cars do not have a visible windshield VIN panel—don’t panic if you can’t find it.
• Tip: To beat windshield glare and avoid transcription errors, scan the VIN instantly and let the app lock onto the characters.

Video Guide

No videos are included for this model in this guide because the provided sources were not for an Audi A4 B5 (8D).

Common Problems & Troubleshooting

• Can’t see the stamped VIN in the plenum chamber: Lift the rubber seal higher, pull the rain tray up further, and scrub the area—these stampings sit in a dirty, shadowed recess.
• Sticker missing or unreadable in the trunk: On cars this age, the paper label often peels, fades, or gets water-damaged—use the stamped firewall VIN as your primary proof.
• Warning: Don’t rely on only one identifier. A valid check is matching the stamped body VIN to the type plate and trunk data sticker (when present). Any mismatch is a red flag.

---