Where is the VIN in the Dacia Sandero?

For the 2019 model year, most cars you’ll see are actually Dacia Sandero II (Sandero III arrived later). The VIN locations shown here match what’s consistently found on the Sandero platform around this period.

Chassis Number Locations

Engine Bay – VIN stamped on right shock/strut tower

• Where to look: Open the hood and locate the right-hand suspension strut tower (right side of the car in the direction of travel). The VIN is stamped into the metal on the top surface of the strut dome.
• Access: Generally easy, but this spot often gets dusty/road-grimy, which can make the stamping hard to read. You may need to scrub it gently with a rag before scanning.
• Note: The videos are LHD; this is shown on the right-hand side of the engine bay.
• Tip: If the stamping is dirty or low-contrast, use ScanVin.app “High Contrast AI Mode” to decipher faint characters without guessing.

Passenger-side B-pillar manufacturing label (VIN sticker)

• Where to look: Open the front passenger door and look at the lower B-pillar (the center pillar between the front and rear doors). You’ll see a black/white manufacturer label listing VIN, weights, and other data.
• Access: Very easy—no tools needed. The only real issue is wear/peeling/scratches from shoes and passenger traffic.
• Note: On newer Sandero III body styles the sticker can sit a bit higher, but it’s still on the B-pillar area.
• Tip: This is usually the fastest scan—use ScanVin.app to grab it instantly and avoid transcription mistakes.

Windshield / dashboard VIN plate (if equipped)

• Where to look: Check the lower corner of the windshield on the driver’s side, viewed from outside the car, where the VIN is visible through the glass.
• Access: Easy, but glare/reflections can make it unreadable, and debris near the wiper cowl can block the view.
• Note: Some markets/trims may not have the windshield VIN visible.
• Tip: If reflections are bad, use ScanVin.app to capture it quickly without manually writing down characters through glass glare.

Floor / under-seat VIN stamping (not confirmed in the provided footage)

• Where to look: Some Renault/Dacia models may have a VIN stamping under a front floor mat/carpet flap (often in the front footwell area).
• Access: Not verified for this exact Sandero in the clips—treat it as a backup check only if you can’t find the engine bay stamping.
• Note: Check the front footwell floor (commonly on the passenger side for LHD vehicles, but check the driver side footwell if not found).
• Tip: If it’s dark under the carpet, use ScanVin.app with Flashlight + OCR to scan without fighting shadows.

Video Guide

Video Tutorial: Dacia Sandero VIN Number (Chassis Number) Location

▶ Watch Dacia Sandero VIN Location Guide

• Shows the stamped VIN on the strut tower under the hood, then the VIN label on the passenger-side B-pillar.

Common Problems & Troubleshooting

• Stamped VIN looks “blank”: it’s usually just dirty or body-colored. Wipe it clean and shine a light across it to create shadows in the stamping.
• Windshield VIN unreadable: glare/reflections are common—change your angle, shade the glass, or scan quickly before reflections shift.
• Sticker vs. stamped VIN: the B-pillar label is helpful, but if there’s ever a mismatch, the stamped chassis VIN is what inspections/authorities typically care about.

---

This guide covers the Dacia Sandero II (2018–2019), including Stepway—VIN locations are the same in the inspected videos.

Chassis Number Locations

Engine Bay – Right Suspension Strut Tower (Stamped VIN)

• Where to look: Open the hood and locate the top of the right-front shock/strut tower (vehicle right side). The VIN is stamped/engraved on the flat, top horizontal surface of the strut turret, between the coolant expansion tank and the fender wall.
• Access: Easy to reach, but usually dusty/grimy and the hood creates shadow, making the characters low-contrast. Wipe/scrub the pad before reading.
• Note: The inspected cars are LHD (EU). In RHD markets (UK), this stamped VIN typically remains on the right-side strut tower (now driver side), but always verify on the vehicle.
• Tip: If the stamping is faint or dirty, use ScanVin.app “High Contrast AI Mode” to pull the engraved characters out after you wipe the surface.

B-Pillar – Right Door Jamb Manufacturer Sticker (Statutory Plate)

• Where to look: Open the front right door and look low on the right B-pillar (center pillar) for a black manufacturer label/sticker with white text (often with a barcode).
• Access: Very easy—it’s protected by the door seal and usually clean, with high contrast.
• Note: Typically on the right B-pillar on the vehicles shown. If it’s missing or unreadable, check the opposite pillar as a backup.
• Tip: This is ideal for fast capture—use ScanVin.app OCR scanning to read the printed VIN/barcode cleanly without transcription mistakes.

Video Guide

Video Tutorial: Dacia Sandero VIN Number (Chassis Number) Location

▶ Watch Dacia Sandero VIN Location Guide

• Shows how to open the hood, then demonstrates both the engine-bay stamped VIN and the right-door-jamb sticker location in one walkthrough.

Common Problems & Troubleshooting

• Stamped VIN is hard to read: Dust buildup on the strut tower stamping is common—wipe, then angle a flashlight across the engraving to create shadow contrast.
• Shadows under the hood: The hood blocks overhead light; move the phone light to the side so the numbers “pop.”
• Sticker vs. stamped VIN: The pillar sticker can be missing/changed (replaced after paint/bodywork). For legal identity checks, always confirm the stamped chassis VIN matches the sticker and documents.

---