Where is the VIN in the Toyota Yaris?

This guide covers where to find the VIN/chassis number locations on the Toyota Yaris (XP210) produced between 2020–2022, including the easiest under-hood label and a hidden stamped number under the front seat area.

Chassis Number Locations

Production Label (VIN Sticker)

• Where to look: Open the hood and look at the firewall/bulkhead at the back of the engine bay, slightly off-center and closer to the passenger side. You’re looking for a silver plate/sticker with black text showing fields like “MODEL”, “ENGINE”, “FRAME No” (VIN), “COLOR”, etc.
• Access: High visibility once the hood is open. You may need to wipe/scrub the label if there’s dust or grime.
• Note: This is usually the best VIN to scan because it’s printed with good contrast.
• Tip: If the plate is dusty or your camera keeps missing letters, wipe it down and then scan it directly with ScanVin.app to avoid mistyping the FRAME No.

Chassis/Frame Number (Stamped, Under Seat)

• Where to look: Check the front footwell floor area under the front seat (commonly on the passenger side for LHD vehicles, but check the driver side footwell if not found). Look for a pre-cut flap in the carpet/matting; lift it to expose the stamped metal chassis number on the floor cross-member.
• Access: Moderate difficulty. You’ll need to slide the seat all the way back, then lift the carpet flap. Lighting is usually poor and the stamping can be low-contrast (body-color paint on metal).
• Note: The reference vehicle shown is RHD, where the stamp is under the driver’s seat—on many LHD cars the equivalent spot is mirrored.
• Tip: Because it’s dark and the angle is awkward, use Flashlight + OCR and capture it with your phone via ScanVin.app instead of trying to read it upside down.

Engine Number (Stamped on Engine Block)

• Where to look: In the engine bay, look down at the front face of the engine block (radiator side). The number is stamped on a flat machined surface, slightly to the left (passenger side) of the exhaust manifold heat shield area, visible past nearby tubes/connectors.
• Access: High difficulty. It’s deep in the bay, often blocked by hoses/wiring, and can be dirty/oily—expect to need strong light and a steady hand.
• Note: This is the engine serial, not the VIN—but it’s commonly requested for registration/verification in some markets.
• Tip: If grime or low contrast makes the stamp hard to read, clean the area and use High Contrast AI Mode—you can use ScanVin.app to pick out faded characters without guessing.

Video Guide

Video Tutorial: Toyota Yaris 2021 Chassis Engine Number Location - YouTube

▶ Watch Toyota Yaris VIN Location Guide

• Shows the under-hood VIN/FRAME plate, the stamped chassis number under the seat carpet flap, and the engine number close-up.

Common Problems & Troubleshooting

• Carpet flap missing or stuck down: Slide the seat fully back, then pry/lift the pre-cut carpet section carefully—some cars have extra matting that hides the seam.
• Stamp/plate hard to read: Under-seat stamps can be low contrast and poorly lit, and engine stamps can be greasy—use a flashlight, clean the surface, and re-check from a straighter angle.
• Sticker vs. stamped number mismatch: If a VIN sticker looks tampered with, bubbled, or freshly replaced, verify against the stamped chassis number before buying or registering.

This guide covers the common VIN (vehicle identification number) locations for the Toyota Yaris Sedan (USA) produced between 2019 and 2019, including the easiest “federal label” spots and the harder stamped chassis locations.

Chassis Number Locations

Driver’s Side Dashboard (through the Windshield)

• Where to look: Visible through the windshield glass at the lower driver’s side corner, on the dash surface near the A‑pillar.
• Access: Easy access from outside the car, but sun glare and a dirty windshield can wash out characters.
• Note: This is the fastest check on most US-market cars.
• Tip: If reflections make the digits hard to transcribe, scan it directly with your phone so you don’t mistype characters like 8/B or 5/S.

Certification Label / VIN Sticker (Driver’s Door Jamb / B‑Pillar)

• Where to look: Open the driver’s door and inspect the driver’s side B‑pillar (center pillar) or the door edge for a black/silver certification label listing the VIN plus build and tire info.
• Access: Simple, but the sticker can be faded, scuffed, or poorly lit in the jamb.
• Note: For LHD vehicles, this is normally on the driver’s side.
• Tip: If the jamb is dark or the label is worn, use the free VIN reader with your phone’s light to capture it cleanly without squinting.

Stamped VIN on the Floor (under/near the Front Passenger Seat area)

• Where to look: A VIN stamped into the metal floor/cross-member, usually hidden under a plastic flap or carpet cut-out. It may be under/near the front seat area.
• Access: Hard to access—you may need to slide the seat, crouch low, and lift a cover. It’s often dark, dirty, and blocked by floor mats.
• Note: Check the front footwell floor (commonly on the passenger side for LHD vehicles, but check the driver side footwell if not found).
• Tip: Since you’ll be in an awkward position and it’s usually shadowy, capture it with your phone using flashlight + OCR instead of trying to write it down.

Engine Bay (Firewall / Cowl Area)

• Where to look: Under the hood, inspect the firewall/cowl panel near the wipers (or sometimes a nearby metal panel like a strut tower area) for a stamped identifier.
• Access: Moderate difficulty—stamps can be obscured by dirt/grease and lighting is often poor under the hood.
• Note: If you can’t find it quickly, prioritize the windshield and door-jamb label first.
• Tip: If the stamp is grimy or low-contrast, scan the characters with high-contrast help so faint digits are easier to confirm.

Engine Number (Not the VIN)

• Where to look: Stamped on a flat machined pad on the engine block (often near the transmission bell housing/exhaust side depending on engine layout).
• Access: Usually deep in the engine bay; may require cleaning for visibility.
• Note: This is the engine number, not the 17‑digit VIN. It’s useful for engine identification, but it won’t replace the VIN for registration/title checks.
• Tip: If the pad is dirty or the stamp is faint, use a phone scan to reduce read errors instead of guessing at worn characters.

Video Guide

Video Tutorial: Toyota Yaris 2019/2020 engine and chassis number

▶ Watch Toyota Yaris Sedan (USA) VIN Location Guide

• Shows the process of finding a chassis/VIN stamping under the seat/floor area and also demonstrates an engine-number stamp.

Video Tutorial: Toyota Yaris 2020 Chassis Engine Number Location

▶ Watch Toyota Yaris Sedan (USA) VIN Location Guide

• Clear footage of the floor VIN access under a carpet/flap plus the engine number location; note the example vehicle is RHD, so “passenger side” orientation differs.

Common Problems & Troubleshooting

• Windshield VIN unreadable: Sun glare and reflections can hide characters—shade the plate with your hand or change your viewing angle.
• Floor VIN hard to access: Floor mats, a tight seat position, and a covered flap/cut-out can block it—slide the seat back, lift the cover, and clean the stamp lightly.
• Sticker doesn’t look valid: A missing, bubbling, or re-applied door-jamb label is a red flag—cross-check the windshield VIN and the stamped VIN before purchase.

---

This guide covers the VIN (chassis number) locations for the Toyota Yaris (XP150) produced between 2017–2018, including the easiest scan points and the hidden stamped chassis marking.

Chassis Number Locations

B-Pillar Vehicle Identification Sticker

• Where to look: Open the front passenger door (for LHD cars: passenger side). On the lower section of the B-pillar (center pillar) you’ll find a black tamper-proof sticker with white text (VIN/chassis details).
• Access: Easy—no tools. Best visibility with the door fully open.
• Note: The inspection vehicle is RHD, where the sticker is shown on the left side. On LHD Yaris models, expect it on the opposite side (commonly the passenger-side B-pillar).
• Tip: If you’re buying the car, this is the quickest place to confirm the VIN—use your phone to scan it directly with ScanVin.app so you don’t mistype any characters.

Floor Stamped Chassis Number (Under Front Seat)

• Where to look: Inside the cabin, under the front right seat area. Slide the seat all the way back, then lift the pre-cut carpet flap (often Velcro/plastic clip) to reveal the VIN/chassis number stamped into the floor cross-member.
• Access: Moderate effort. You must move the seat and lift the carpet flap. Lighting is usually poor because the seat casts a shadow.
• Note: The report shows this on an RHD vehicle under the front right seat. For LHD vehicles, check the front footwell floor (commonly on the passenger side for LHD vehicles, but check the driver side footwell if not found).
• Tip: This spot is dark and awkward to read—use Flashlight + OCR and capture it with your phone using ScanVin.app so you don’t have to write it down while bent over in the doorway.

Engine Number on Engine Block (Not the VIN)

• Where to look: In the engine bay, locate the engine block. The engine number is stamped on a flat machined surface near the front/center-left area (when facing the car), just below the exhaust manifold heat shield, facing forward.
• Access: Harder than the sticker. It’s a dark area, often partly blocked by hoses/heat shield, and may be dirty with road grime/oil.
• Note: This is the engine number, not the cabin VIN label—use it for matching documents/registration checks where required.
• Tip: If the stamping is dirty or dot-matrix style, wipe the area and use High Contrast AI—then use the free VIN/number reader on ScanVin.app to improve readability when the characters don’t pop on camera.

Video Guide

Video Tutorial: TOYOTA YARIS ATIV NSP150L (XP150) CHASSIS NUMBER LOCATION & ENGINE NUMBER LOCATION CareDrive

▶ Watch Toyota Yaris VIN Location Guide

• Shows a clear inspection sequence of the B-pillar sticker, the under-seat floor stamping, and the engine-number stamping on an XP150 Yaris.

Common Problems & Troubleshooting

• Under-seat VIN is “missing”: It’s usually just covered—slide the seat back and lift the carpet flap (it can be stiff or clipped down).
• Engine number won’t read on camera: The area is often greasy/dusty and shadowed—scrub lightly with a rag and use a flashlight to avoid casting your own shadow.
• Sticker looks tampered or illegible: A damaged/peeling B-pillar label can be a red flag—always cross-check the sticker VIN against the stamped floor chassis number before you buy.

---

This guide covers the VIN (chassis number) locations for the Toyota Yaris iA produced between 2017 and 2017, including the quick-to-check spots and the hidden stamped chassis locations.

Chassis Number Locations

1) Floor stamping (under right-hand front seat / commonly passenger seat on LHD)

• Where to look: Slide the right-hand front seat all the way back. Look on the floor for a pre-cut flap in the carpet/floor mat area. Lift the flap to reveal the VIN stamped directly into the metal chassis cross-member.
• Access: You’ll need to move the seat for room, then lift the carpet flap. Expect poor lighting, heavy shadows, and dirt/debris—wipe the stamping clean before reading.
• Note: For LHD (US/Canada) cars, the right-hand front seat is typically the front passenger seat. If you don’t find it there, check the opposite front seat area as well.
• Tip: Because it’s dark under the seat and the stamp can be dusty, use your phone light and scan it directly with ScanVin.app to let OCR grab the characters without you squinting under the seat.

2) Driver’s side dashboard (visible through windshield)

• Where to look: Stand outside the car and look through the windshield at the top-left of the dashboard (driver’s side on LHD cars). You’ll see the VIN on a small plate.
• Access: Easiest access—no tools. The main issue is windshield glare/reflections (sunlight, streetlights, tinted glass).
• Note: This is the most “standard” public VIN display location on most US/EU vehicles.
• Tip: If reflections make the characters hard to read, capture it instantly with the VIN scanner so you don’t mistype a letter/number (common mix-ups: 8/B, 5/S, 0/O).

3) Certification label (driver’s door jamb / B-pillar)

• Where to look: Open the driver’s door and check the driver-side door jamb/B-pillar area for the VIN sticker/certification label.
• Access: Very easy—just open the door and aim a light if needed. Sticker condition can vary with age (scuffs, peeling, fading).
• Note: This label is great for quick verification, but it’s not the same as the stamped chassis VIN.
• Tip: If the label is worn or low-contrast, use the free VIN reader to improve capture accuracy without manually copying faded print.

4) Engine bay stamping (firewall / cowl area)

• Where to look: In the engine compartment, look deep toward the firewall, slightly toward the center-right (passenger-side area). The stamping is on a flat metal surface/bar below the cowl/air intake area and can be partially blocked by hoses/intake components.
• Access: Hard to reach and hard to see. You’ll be working at an awkward angle with limited line-of-sight; expect grime. A strong light and cleaning rag help.
• Note: This is a secondary verification spot when you need to compare multiple VIN locations.
• Tip: Since it’s deep, dark, and often dirty, clean the area and scan with high-contrast OCR using ScanVin.app so you don’t have to write it down while leaning over the engine bay.

Common Problems & Troubleshooting

• Can’t find the floor VIN: The carpet flap may be hidden under floor mats or packed with debris—pull the mat back, slide the seat fully rearward, lift the pre-cut flap, and wipe the metal stamp clean.
• VIN is there but unreadable: Dirt, shadows, and awkward angles (especially under-seat and engine bay) can hide characters—use a strong flashlight and clean the surface before scanning/reading.
• Door-jamb sticker doesn’t match or looks tampered: Stickers can be replaced—always cross-check the windshield VIN and the stamped chassis VIN (floor) when verifying a vehicle.

---

This guide shows where to find the VIN/chassis number on the Toyota Yaris III (2012–2017), including the common “hidden” stamped locations used for registration and verification.

Chassis Number Locations

Front Passenger Floor (Under Seat)

• Where to look: On the floor cross member under the front right seat (commonly passenger side for LHD). Slide the seat all the way back, lift the pre-cut carpet flap, then pry up the small plastic cover stamped “FRAME NO. / VIN” to reveal the VIN stamped into the metal.
• Access: You’ll need to move the seat for room; it’s a dark area and the flap/cover can be stiff to lift fully. Usually clean because it’s protected by the carpet.
• Note: On many Yaris III, this stamp is on the right side. For RHD cars, that can mirror relative to seating position—if you don’t find it under the right seat, check the opposite front seat area.
• Tip: Because it’s cramped and poorly lit, use the in-app light and let OCR do the work—scan the VIN directly with your phone instead of trying to read it at an awkward angle.

B-Pillar / Door Jamb Sticker

• Where to look: Open the front left door (LHD driver side) and look on the lower B-pillar (center pillar) for the black manufacturer label. It lists the VIN plus model/engine codes and color/trim.
• Access: Easy visibility with the door open; main issues are glare on the glossy label or an old sticker that’s faded/peeled.
• Note: On RHD cars, this label can be on the opposite side of the cabin compared to LHD examples.
• Tip: If glare makes characters hard to read, capture it with the free VIN reader so you don’t mistype similar characters like 8/B or 5/S.

Engine Bay (Firewall/Bulkhead Stamp)

• Where to look: In the engine bay, locate the VIN stamped into the metal firewall/bulkhead, slightly right of center (when facing the engine), tucked below the plastic cowling and behind the engine.
• Access: This spot is recessed and shadowed; hoses/wiring can partly block your view. The stamping can be dirty with dust/oil, so scrub it lightly before trying to read it.
• Note: This is a stamped identifier (not a sticker), useful for checking the car hasn’t been re-tagged.
• Tip: If grime kills contrast, wipe it clean and use High Contrast AI scanning to decipher faint stamped characters without guessing.

Windshield (Dashboard Corner)

• Where to look: At the bottom corner of the windshield on the driver’s side (LHD: left), where the dash meets the glass (VIN plate visible from outside).
• Access: Usually quick to view, but windshield glare/reflections are common; dirt near the cowl can also obscure it.
• Note: This is the fastest “at-a-glance” VIN, but always cross-check against a stamped location if you suspect tampering.
• Tip: When reflections wash it out, grab a clean scan instantly rather than trying to transcribe it through the glass.

Video Guide

Video Tutorial: Toyota Yaris 1.0 Engine number, chassis number and ... - YouTube

▶ Watch Toyota Yaris VIN Location Guide

• Walkaround showing the engine bay VIN stamp and the B-pillar manufacturer label on a Yaris (RHD example—locations may mirror for LHD).

Video Tutorial: Toyota Yaris Vin Number Location - YouTube

▶ Watch Toyota Yaris VIN Location Guide

• Quick demo of the stamped VIN hidden under the front right seat floor flap (the “FRAME NO. / VIN” cover).

Common Problems & Troubleshooting

• Can’t see the floor VIN: Slide the seat fully back, lift the carpet flap completely, and use a flashlight—this area is dark and the plastic cover can be tight.
• Engine bay stamp looks “blank”: It’s often coated in grime; scrub gently and re-check from an angle (shadows and low contrast hide the stamp).
• Sticker VIN doesn’t “count” or looks tampered with: Door-jamb labels can fade/peel or be replaced—verify the VIN against a stamped location (floor/engine bay) before buying.

---

This guide shows where to find the VIN/chassis number on the Toyota Yaris II (2006–2011), including the quick-to-check sticker location and the hidden stamped VIN under the carpet.

Chassis Number Locations

B-Pillar / Door Jamb (VIN Sticker)

• Where to look: Open the front passenger door (LHD) and check the lower part of the B-pillar for a black sticker with white text (it also lists weight ratings and paint code).
• Access: Low difficulty. Easy to reach and read; the main issue is wear/peeling on older cars.
• Note: On the video’s LHD car, this sticker is on the front passenger side.
• Tip: If the label is slightly faded or you don’t want to mistype characters, use the camera to scan the VIN instantly instead of copying it by hand.

Cabin Floor (Stamped Chassis/VIN) — Under Front Right Seat Carpet Flap

• Where to look: Inside the cabin, go to the front right seat area and find the pre-cut flap in the carpet; lift the flap to reveal the VIN stamped into the metal cross-member/floor pan.
• Access: Medium difficulty. It’s dark and awkward to reach; the carpet flap can be stiff or stuck, and debris/rust can hide the stamping if the floor has been wet.
• Note: This Yaris has the stamping on the right side of the floor pan—commonly the passenger side on LHD, but if you don’t find it there, check the driver-side footwell/seat area on your market variant.
• Tip: Because it’s shadowed under the seat, turn on your phone light and scan it with the flashlight + OCR so you don’t have to hold the flap open and write the VIN in an awkward position.

Windshield (Dashboard VIN Plate)

• Where to look: Look through the bottom corner of the windshield at the dashboard area (common market location for this generation).
• Access: Variable difficulty. Often readable, but glare/reflections through glass can make it hard to capture cleanly.
• Note: If it’s hard to see, try changing angles or shading the glass with your hand.
• Tip: To avoid transcription mistakes when reflections hit the glass, capture it with your phone and let the app read the characters for you.

Engine Number Location (Not the VIN)

Engine Bay (Engine Number on Engine Block)

• Where to look: In the engine bay, locate the front face of the engine block, slightly right of center (standing in front of the car). The stamping is vertical on a flat machined surface, tucked behind a metal bracket near the exhaust manifold heat shield (the video shows “1KR”).
• Access: High difficulty. Deep in the bay with shadows from hoses/heat shield; older cars may have grime/rust, and you’ll need a specific viewing angle.
• Note: This is the engine number, not the VIN—use it for matching engine identity to documents when required.
• Tip: If the characters are low-contrast due to dirt or corrosion, clean the area and then use High Contrast AI scanning to decipher the stamp without guessing.

Video Guide

Video Tutorial: 2007 Toyota Yaris, chasis and engine number location - YouTube

▶ Watch Toyota Yaris VIN Location Guide

• Walk-around showing the engine number on the block, the stamped chassis/VIN under the front right seat carpet flap, and the VIN label on the B-pillar.

Common Problems & Troubleshooting

• Carpet flap won’t lift / VIN is dirty: Pry up the flap carefully, vacuum debris, and wipe the metal stamping; a small brush helps if the floor has surface rust.
• Engine number can’t be seen: Use a flashlight, adjust your viewing angle, and degrease the area near the heat shield—heat/shadows make the stamp easy to miss.
• Sticker doesn’t match stamped VIN: Door-jamb stickers can be replaced; the stamped floor VIN is the one you should trust when verifying identity (and ensure it matches registration documents).

---

This guide shows you where to find the VIN (chassis number) on the Toyota Yaris I produced between 2003 and 2005, using the most consistent factory locations mechanics check.

Chassis Number Locations

Under Front Right Seat (Floor / Chassis)

• Where to look: Slide the front right seat fully back and look on the floor under the seat rails. Find a carpet cut-out flap (or, on some markets, a rigid plastic cover labeled “FRAME NO. / VIN”). Lift/pry it up to reveal the VIN stamped into the chassis/cross-member.
• Access: Medium. You’ll need to move the seat all the way back and work in a tight, dark space. The flap/cover can be stiff—use a trim tool or a flat screwdriver carefully so you don’t tear the carpet.
• Note: On LHD cars, this is commonly on the passenger side (front right). If you don’t find it there, check the opposite front footwell area as markets/trims vary.
• Tip: Because it’s dark and you’re working at an awkward angle, use the phone flashlight and OCR to avoid misreading characters—scan it directly with ScanVin.app.

B-Pillar / Door Jamb Label (Passenger Side)

• Where to look: Open the passenger door and check the B-pillar/door jamb for a black sticker with white text showing the VIN plus model/engine codes.
• Access: Low. No tools needed—just fully open the door and wipe dust off the label if needed.
• Note: This is a sticker label (not a metal stamp). It’s great for quick confirmation, but always compare it to a stamped VIN when inspecting a car.
• Tip: If you’re cross-checking multiple VIN points quickly, capture it with your phone using the VIN scanner instead of typing long strings.

Engine Bay (Bulkhead / Firewall Stamping)

• Where to look: Open the hood and look at the center of the firewall/bulkhead behind the engine, slightly below the windshield cowl line. The VIN is stamped directly into the metal and can sit deep in the recess.
• Access: High. This spot is usually shadowed by the cowl/engine components; you’ll need strong lighting and a steady hand to see the stamp clearly.
• Note: This is one of the “hard proof” stamped locations—worth checking when buying or verifying identity.
• Tip: If the stamping is faint or you can’t get your eyes in line with it, use ScanVin.app to scan it in-place so you don’t have to write it down while leaning into the engine bay.

Windshield (Dashboard Corner)

• Where to look: From outside the car, look through the bottom corner of the windshield on the driver’s side for the VIN plate visible through the glass.
• Access: Medium. Easy to reach, but glare/reflections on the windshield can hide characters.
• Note: Best used as a quick first check, then verify against the floor/firewall stamp.
• Tip: To beat glare and avoid transcription mistakes, scan the VIN instantly with your camera and let OCR pick out the characters.

Video Guide

Video Tutorial: Toyota Yaris Vin Number Location

▶ Watch Toyota Yaris VIN Location Guide

• Shows the engine bay firewall/bulkhead VIN stamping location on a hatchback, including the tight viewing angle.

Video Tutorial: How to Find Chassis VIN Number Toyota Yaris

▶ Watch Toyota Yaris VIN Location Guide

• Step-by-step demonstration of lifting the under-seat floor flap and revealing the stamped chassis VIN (very dark area).

Video Tutorial: Toyota Yaris 1.0 Engine number, chassis number and chassis plate location

▶ Watch Toyota Yaris VIN Location Guide

• Walkaround showing multiple VIN points (floor cover, pillar sticker, engine bay) on an RHD sedan variant—useful for understanding the different covers/labels.

Common Problems & Troubleshooting

• Too dark under the seat: Slide the seat all the way back, use a flashlight, and clean the stamped area lightly so the characters pop (dust hides shallow stamps).
• Firewall VIN is hard to see: Use a strong light and aim from above; don’t mistake casting marks for the VIN—Toyota stamps are clean, straight, and evenly spaced.
• Sticker mismatch warning: Door-jamb labels can be replaced; if the sticker VIN doesn’t match the stamped floor/firewall VIN, treat it as a serious red flag and verify the vehicle history.

---